Se connecter avec
S'enregistrer | Connectez-vous

Connection wifi sous Slackware (Linux)

Dernière réponse : dans Connexions réseau et internet

Voila, j'aimerais me connecter avec la wifi avec slackware, mais probleme, ma carte wifi est bien installer mais je n'arrive pas a me connecter.

Voici le resultat de mon iwconfig :

  1. root@darkstar:/etc# iwconfig
  2. lo        no wireless extensions.
  3.  
  4. eth0      no wireless extensions.
  5.  
  6. wlan0     IEEE 802.11g  ESSID:off/any
  7.           Mode:Managed  Frequency:2.412 GHz  Access Point: Not-Associated
  8.           Bit Rate:1 Mb/s   Sensitivity=-200 dBm
  9.           RTS thr=2346 B   Fragment thr=2346 B
  10.           Encryption key:0000-2163-E9BD-F0   Security mode:restricted
  11.           Power Management:off
  12.           Link Quality:0  Signal level:0  Noise level:0
  13.           Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
  14.           Tx excessive retries:0  Invalid misc:0   Missed beacon:0


  1. root@darkstar:/# lspci -vv   
  2. 05:01.0 Ethernet controller: Marvell Technology Group Ltd. 88w8335 [Libertas] 802.11b/g Wireless (rev 03)
  3.         Subsystem: Netgear WG311v3 802.11g Wireless PCI Adapter
  4.         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
  5.         Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
  6.         Latency: 64, Cache Line Size: 32 bytes
  7.         Interrupt: pin A routed to IRQ 17
  8.         Region 0: Memory at febf0000 (32-bit, non-prefetchable) [size=64K]
  9.         Region 1: Memory at febe0000 (32-bit, non-prefetchable) [size=64K]
  10.         Capabilities: [40] Power Management version 2
  11.                 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
  12.                 Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
  13.         Kernel driver in use: ndiswrapper

  1. root@darkstar:/# ifconfig
  2. lo        Link encap:Local Loopback
  3.           inet addr:127.0.0.1  Mask:255.0.0.0
  4.           inet6 addr: ::1/128 Scope:Host
  5.           UP LOOPBACK RUNNING  MTU:16436  Metric:1
  6.           RX packets:1758 errors:0 dropped:0 overruns:0 frame:0
  7.           TX packets:1758 errors:0 dropped:0 overruns:0 carrier:0
  8.           collisions:0 txqueuelen:0
  9.           RX bytes:148692 (145.2 KiB)  TX bytes:148692 (145.2 KiB)
  10.  
  11. wlan0     Link encap:Ethernet  HWaddr 00:1b:2f:d0:c1:c8
  12.           UP BROADCAST MULTICAST  MTU:1500  Metric:1
  13.           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
  14.           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
  15.           collisions:0 txqueuelen:1000
  16.           RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
  17.           Interrupt:17 Memory:febe0000-febf0000

  1. root@darkstar:/# ping 127.0.0.1
  2. PING 127.0.0.1 (127.0.0.1) 56(84) bytes of data.
  3. 64 bytes from 127.0.0.1: icmp_seq=1 ttl=64 time=0.020 ms
  4. 64 bytes from 127.0.0.1: icmp_seq=2 ttl=64 time=0.021 ms
  5. 64 bytes from 127.0.0.1: icmp_seq=3 ttl=64 time=0.022 ms

  1. root@darkstar:/etc# cat resolv.conf
  2. search example.net

  1. root@darkstar:/etc# sudo route
  2. Kernel IP routing table
  3. Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
  4. loopback        *               255.0.0.0       U     0      0        0 lo

  1. root@darkstar:/# sudo dhclient wlan0                        
  2. Internet Systems Consortium DHCP Client V3.1.2p1            
  3. Copyright 2004-2009 Internet Systems Consortium.            
  4. All rights reserved.                                        
  5. For info, please visit <a href="http://www.isc.org/sw/dhcp/" target="_blank">http://www.isc.org/sw/dhcp/</a>          
  6.  
  7. Listening on LPF/wlan0/00:1b:2f:xxxxxxx
  8. Sending on   LPF/wlan0/00:1b:2:xxxxxx
  9. Sending on   Socket/fallback            
  10. DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 8
  11. DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 9
  12. DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 15
  13. DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 
  14. DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 10
  15. DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12
  16. No DHCPOFFERS received.                                     
  17. No working leases in persistent database - sleeping.


  1. root@darkstar:/# iwlist wlan0 scanning
  2. wlan0     Scan completed :   
  3.  
  4. Cell 01 - Address: 00:21:63:XX:XX:XX 
  5. ESSID:"French_Connection"
  6. Protocol:IEEE 802.11g
  7. Mode:Managed
  8. Frequency:2.412 GHz (Channel 1)
  9. Quality:42/100  Signal level:-69 dBm  Noise level:-96 dBm
  10. Encryption key:on
  11. Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
  12. 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
  13. 48 Mb/s; 54 Mb/s
  14. Extra:bcn_int=100
  15. Extra:atim=0



C'est pas un probleme de dhcp car j'ai deja 4 ordinateurs connectés par winxp et pas de soucis.

Autres pages sur : connection wifi slackware linux

Lassé par la pub ? Créez un compte

Voici les infos de ma box.

LAN Interface
IP Address Subnet MAC Address Status
10.0.0.138 255.255.255.0 00:21:63:e9:bd:f0

WAN Interface
PVC VPI/VCI IP Address Subnet Gateway Encapsulation Status
PVC-0 8 /48 90.179.60.182 255.255.255.255 194.228.196.6 Route -PPPoE
PVC-1 8 /35 0.0.0.0 0.0.0.0 0.0.0.0 Bridge -RFC2684

Je dois peut etre modifier quelques choses ?
Lassé par la pub ? Créez un compte

Répondre Créer un nouveau sujet

Tom's guide dans le monde